Microsim – 06D Weight-measuring batching instrument Designation: It is used as a part of discrete batcher or technological equipment with various load cells. Benefits: Wide scope of automation, stock-taking, weighing results registration; Calibration values of “Microsim-06D”-based weighing system are protected with password and “electronic seal”. They are saved in volatile storage, number of rewriting cycles is not less than 100000; Reliable dust- and drip-proof aluminum case with membranous front panel; U-shaped support allows to regulate instrument body slope; Harnesses allow to mount the instrument in a cabinet; Galvanic isolated discrete inputs/outputs. Standard functions: Output of “gross”, “net”, “tare” values for indication; automatic and manual indication zeroing; zero self-tuning; accumulation and indication of resulting amount of several weighing processes, total value display; Rate of exchange up to 9600 baud; Parallel connection of several load cells (from 1 to 8) with total resistance not less than 80 Ohm; The device is equipped with galvanic isolated COM-port for operation via RS485 interface; The device is equipped with input-output module "М2604" with galvanic isolated inputs/outputs.

Extended functions:

• A programmable input/output module “М2606” with programmed batching algorithm can be setup.

A floppy disc with driver DevCom and examples of its call from 1C, Access and other programs is included in the delivery set.

	Modifications and their basic specifications Characteristics М0600-D4-02 М0600-D4-04 Galvanic isolated COM-port RS485 + + Driver DevCom + + Programmable input/output module М2606   + Galvanic isolated discrete inputs/outputs + +

	External batcher inputs: ON Switch from “scales” mode to “batcher” mode TARE Current weight should be taken as “tare” START Save current “gross” weight as a “base” for stock-taking, start the batching process STOP Calculate “actual doze”, finish the batching process OFF Switch from “batcher” mode to “scales” mode

	External batcher outputs MEANDER The batcher is able to work and is in “batcher” mode EXIT-0 Set value-0 is exceededа EXIT-1 Set value-1 is exceeded EXIT-2 Set value-2 is exceeded RESPONSE A signal is received and is being processes ERROR If there is a logical inconsistency between the set values CYCLE The device is in batching process

"Microsim-0600-D6-04" has 8х8 DIO (programmable inputs and outputs). Inputs/outputs designation depends on the batching algorithm.

Standard algorithms:

• “rough”, “accurate” batching;
• Dose collection with the following packing;
• Unit dosing and other.

If you need to connect several scales to one PC using network bus RS485, you should use interface connector “INCON-MT” and the driver "DEVNet", supplied on request.

Driver DevCom provides basic set of communication functions. It allows to setup connection, to transfer operator’s commands to the scale terminal, to take weighing results, display them and also transfer them to the backup indicator panel (if any). It also has the same functions if DevCom is started from the user application (examples for 1C, Access, Delphi are enclosed).

	Technical specification Characteristic Unit Value Load cell supply voltage (DC or AC of Meander type) V 5±0,5 Minimum load cell(s) resistance Ohm 80 Working range of load cell signal mV/V -0,05…2,55 Number of inputs for load cell connection pcs 6 Length of load cell connection line, not more m 100 Main reduced error of load cell signal conversion to a code, not more % 0,01 Height of indication symbolsи mm 14 Weight with external power supply and a pedestal, not more kg 1,5 Power consumption, not more VA 15 Supply voltage V 220+22-33

	Additional equipment Марка, обозначение Характеристика INCON-MT Interface connector for RS232-C to RS-485 conversion at the computer side M1900 Backup indicator panel, small(height of indication symbols = 14mm) М1901 Backup indicator panel, large (height of indication symbols = 100mm) DevNet Driver for network connection through RS485 RS485 Cable for connection via RS485 (2 or 10m long)